Unique Top-selling 350-401 Exams - New 2025 Cisco Pratice Exam
CCNP Enterprise Dumps 350-401 Exam for Full Questions - Exam Study Guide
NEW QUESTION # 255
Refer to the exhibit.
Refer to the exhibit. Which command allows hosts that are connected to FastEthernet0/2 to access the Internet?
- A. ip nat outside source list 10 interface FastEthernet0/2 overload
- B. ip nat outside source static 209.165.200.225 10.10.10.0 overload
- C. ip nat inside source list 10 interface FastEthernet0/1 overload
- D. ip nat inside source list 10 interface FastEthernet0/2 overload
Answer: C
NEW QUESTION # 256
Drag and drop the characteristics from the left onto the switching mechanisms they describe on the right.
Answer:
Explanation:
NEW QUESTION # 257
An engineer is describing QoS to a client. Which two facts apply to traffic policing? (Choose two.)
- A. Policing adapts to network congestion by queuing excess traffic
- B. Policing should be performed as close to the source as possible
- C. Policing drops traffic that exceeds the defined rate
- D. Policing typically delays the traffic, rather than drops it
- E. Policing should be performed as close to the destination as possible
Answer: B,C
Explanation:
Traffic policing propagates bursts. When the traffic rate reaches the configured maximum rate (or committed information rate), excess traffic is dropped (or remarked). The result is an output rate that appears as a saw-tooth with crests and troughs.
Unlike traffic shaping, traffic policing does not cause delay.
Classification (which includes traffic policing, traffic shaping and queuing techniques) should take place at the network edge. It is recommended that classification occur as close to the source of the traffic as possible.
Also according to this Cisco link, "policing traffic as close to the source as possible".
NEW QUESTION # 258
Refer to the exhibit.
Which JSON syntax is derived from this data?
- A.
- B.
- C.
- D.
Answer: A
Explanation:
The correct JSON syntax derived from the data would be the one that accurately represents the structure and data types as defined in the exhibit. In the context of the SPCOR course, JSON syntax is used to represent network configuration and state information in a structured, text-based format. It is important for the JSON to be correctly formatted with proper key-value pairs, arrays, and nested objects as required.
References := The Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR) course
NEW QUESTION # 259
Refer to the exhibit.
What are two effect of this configuration? (Choose two.)
- A. Inside source addresses are translated to the 209.165.201.0/27 subnet.
- B. The 209.165.201.0/27 subnet is assigned as the outside local address range.
- C. The 10.1.1.0/27 subnet is assigned as the inside global address range.
- D. It establishes a one-to-one NAT translation.
- E. The 10.1.1.0/27 subnet is assigned as the inside local addresses.
Answer: A,E
NEW QUESTION # 260
Drag and drop the automation characteristics from the left onto the appropriate tools on the right.
Answer:
Explanation:
Explanation:
NEW QUESTION # 261 
Refer to the exhibit. A network engineer must configure NETCONF. After creating the configuration, the engineer gets output from the command show line, but not from show running-config. Which command completes the configuration?
- A. Option D
- B. Option A
- C. Option C
- D. Option B
Answer: C
NEW QUESTION # 262
Drag and drop the LISP components from the left onto the function they perform on the right. Not all options are used.
Answer:
Explanation:
+ accepts LISP encapsulated map requests: LISP map resolver
+ learns of EID prefix mapping entries from an ETR: LISP map server
+ receives traffic from LISP sites and sends it to non-LISP sites: LISP proxy ETR
+ receives packets from site-facing interfaces: LISP ITR
Explanation
ITR is the function that maps the destination EID to a destination RLOC and then encapsulates the original packet with an additional header that has the source IP address of the ITR RLOC and the destination IP address of the RLOC of an Egress Tunnel Router (ETR).
After the encapsulation, the original packet become a LISP packet.
ETR is the function that receives LISP encapsulated packets, decapsulates them and forwards to its local EIDs. This function also requires EID-to-RLOC mappings so we need to point out an "map-server" IP address and the key (password) for authentication.
A LISP proxy ETR (PETR) implements ETR functions on behalf of non-LISP sites. A PETR is typically used when a LISP site needs to send traffic to non-LISP sites but the LISP site is connected through a service provider that does not accept no routable EIDs as packet sources. PETRs act just like ETRs but for EIDs that send traffic to destinations at non-LISP sites.
Map Server (MS) processes the registration of authentication keys and EID-to-RLOC mappings. ETRs sends periodic Map-Register messages to all its configured Map Servers.
Map Resolver (MR): a LISP component which accepts LISP Encapsulated Map Requests, typically from an ITR, quickly determines whether or not the destination IP address is part of the EID namespace
NEW QUESTION # 263
Drag and drop the characteristics from the left onto the infrastructure deployment models on the right.
Answer:
Explanation:
NEW QUESTION # 264
Refer to the exhibit. What is the effect of introducing the sampler feature into the Flexible NetFlow configuration on the router?
- A. Every second IPv4 packet is forwarded to the collector for inspection.
- B. CPU and memory utilization are reduced when compared with what is required for full NetFlow.
- C. The resolution of sampling data increases, but it requires more performance from the router.
- D. NetFlow updates to the collector are sent 50% less frequently.
Answer: B
NEW QUESTION # 265
Which router is elected the IGMP Querier when more than one router is in the same LAN segment?
- A. The router with the highest IP address
- B. The router with the lowest IP address
- C. The router with the shortest uptime
- D. The router with the longest uptime
Answer: B
Explanation:
Explanation
Query messages are used to elect the IGMP querier as follows: 1. When IGMPv2 devices start, they each multicast a general query message to the all-systems group address of 224.0.0.1 with their interface address in the source IP address field of the message. 2. When an IGMPv2 device receives a general query message, the device compares the source IP address in the message with its own interface address. The device with the lowest IP address on the subnet is elected the IGMP querier. 3. All devices (excluding the querier) start the query timer, which is reset whenever a general query message is received from the IGMP querier. If the query timer expires, it is assumed that the IGMP querier has gone down, and the election process is performed again to elect a new IGMP querier.
Reference:
https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst3750x_3560x/software/release/15-2_2_e/multicast/c
NEW QUESTION # 266
Refer to the exhibit.
Based on the configuration in this WLAN security setting, Which method can a client use to authenticate to the network?
- A. text string
- B. RADIUS token
- C. certificate
- D. username and password
Answer: A
NEW QUESTION # 267
Refer to the exhibit.
An engineer must ensure that all traffic leaving AS 200 will choose Link 2 as the exit point. Assuming that all BGP neighbor relationships have been formed and that the attributes have not been changed on any of the routers, which configuration accomplish task?
- A. R4(config-router)bgp default local-preference 200
- B. R3(config-router)neighbor 10.1.1.1 weight 200
- C. R3(config-router)bgp default local-preference 200
- D. R4(config-router)nighbor 10.2.2.2 weight 200
Answer: A
Explanation:
Local preference is an indication to the AS about which path has preference to exit the AS in order to reach a certain network. A path with a higher local preference is preferred. The default value for local preference is 100.
Unlike the weight attribute, which is only relevant to the local router, local preference is an attribute that routers exchange in the same AS. The local preference is set with the "bgp default local-preference value" command.
In this case, both R3 & R4 have exit links but R4 has higher local-preference so R4 will be chosen as the preferred exit point from AS 200.
NEW QUESTION # 268 
Refer to the exhibit Drag and drop the snippets into the RESTCONF request to form the request that returns this response Not all options are used
Answer:
Explanation:
NEW QUESTION # 269 
Answer:
Explanation:
See the solution below in Explanation.
Explanation:
Solution:
Copy run start
Copy run start
Copy run start
Verification:-
OR
NEW QUESTION # 270
Which two sources cause interference for Wi-Fi networks? (Choose two).
- A. mirrored wall
- B. fish tank
- C. 900MHz baby monitor
- D. Incandesent lights
- E. DECT 6.0 cordless
Answer: A,B
Explanation:
Windows can actually block your WiFi signal. How? Because the signals will be reflected by the glass.
Some new windows have transparent films that can block certain wave types, and this can make it harder for your WiFi signal to pass through. Tinted glass is another problem for the same reasons. They sometimes contain metallic films that can completely block out your signal. Mirrors, like windows, can reflect your signal. They`re also a source of electromagnetic interference because of their metal backings.
Reference: https://dis-dot-dat.net/what-materials-can-block-a-wifi-signal/ An incandescent light bulb, incandescent lamp or incandescent light globe is an electric light with a wire filament heated until it glows. WiFi operates in the gigahertz microwave band. The FCC has strict regulations on RFI (radio frequency interference) from all sorts of things, including light bulbs -> Incandesent lights do not interfere Wi-Fi networks.
Note:
+ Many baby monitors operate at 900MHz and won`t interfere with Wi-Fi, which uses the 2.4GHz band.
+ DECT cordless phone 6.0 is designed to eliminate wifi interference by operating on a different frequency. There is essentially no such thing as DECT wifi interference.
NEW QUESTION # 271
Drag and drop the LISP components from the left onto the function they perform on the right. Not all options are used.
Answer:
Explanation:
NEW QUESTION # 272
What is the function of an EIGRP sequence TLV packet?
- A. to define the initial sequence number when bringing up a new peer
- B. to list the peers that should listen to the next multicast packet during the reliable multicast process
- C. to acknowledge a set of sequence numbers during the startup update process
- D. to list the peers that should not listen to the next multicast packet during the reliable multicast process
Answer: D
NEW QUESTION # 273
Which OSPF networks types are compatible and allow communication through the two peering devices?
- A. point-to-multipoint to broadcast
- B. point-to-multipoint to nonbroadcast
- C. broadcast to nonbroadcast
- D. broadcast to point-to-point
Answer: C
Explanation:
Explanation
The following different OSPF types are compatible with each other:
+ Broadcast and Non-Broadcast (adjust hello/dead timers)
+ Point-to-Point and Point-to-Multipoint (adjust hello/dead timers)
Broadcast and Non-Broadcast networks elect DR/BDR so they are compatible.
Point-topoint/ multipoint do not elect DR/BDR so they are compatible.
NEW QUESTION # 274
Drag and drop the characteristics from the left onto the deployment types on the right.
Answer:
Explanation:
NEW QUESTION # 275
Which QoS component alters a packet to change the way that traffic is treated in the network?
- A. Policing
- B. Marking
- C. Shaping
- D. Classification
Answer: B
Explanation:
QoS Packet Marking refers to changing a field within a packet either at Layer 2 (802.1Q/p CoS, MPLS EXP) or Layer 3 (IP Precedence, DSCP and/or IP ECN).
Reference:
xe-16-book/qos-mrkg.html
NEW QUESTION # 276
Drag and drop the characteristics from the left onto the routing protocols they describe on the right.
Answer:
Explanation:
NEW QUESTION # 277
Refer to the exhibit.
Clients are reporting an issue with the voice traffic from the branch site to the central site. What is the cause of this issue?
- A. There is a high delay on the WAN links.
- B. The voice traffic is using the link with less available bandwidth.
- C. Traffic is load-balancing over both links, causing packets to arrive out of order.
- D. There is a routing loop on the network.
Answer: C
Explanation:
Traffic is load-balancing over both links, causing packets to arrive out of order. This can cause voice quality issues, such as jitter and delay. To avoid this problem, voice traffic should be sent over a single path, using a routing protocol that supports unequal-cost load balancing, such as EIGRP. The source of this answer is the Cisco ENCOR v1.1 course, module 4, lesson 4.3: Implementing EIGRP.
NEW QUESTION # 278
......
Cisco 350-401 certification exam, also known as Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR), is a comprehensive exam designed to test an individual's knowledge and skills in implementing and operating enterprise-level Cisco networks. 350-401 exam is part of the Cisco Certified Network Professional (CCNP) certification track and is a crucial step for network professionals who want to demonstrate their expertise in implementing and managing complex enterprise networks.
Best way to practice test for Cisco 350-401: https://www.braindumpspass.com/Cisco/350-401-practice-exam-dumps.html
350-401 Dump Ready - Exam Questions and Answers: https://drive.google.com/open?id=19ognuMfw1_liX3jxmcV05k473d4SZDTn
