Juniper JN0-648 Real Exam Questions Test Engine Dumps Training With 90 Questions
JN0-648 Actual Questions Answers PDF 100% Cover Real Exam Questions
NEW QUESTION 15
Click the Exhibit button.
You are adding VNI 101 to your EVPN-VXLAN network, but traffic is not being sent or received.
Referring to the exhibit, which configuration statement will solve the problem?
- A. set routing-instances EVPN1 bridge-domains BD-101 vxlan vni 101
- B. set routing-instances EVPN1 vrf-table-label
- C. set routing-instances EVPN1 vxlan encapsulate-inner-vlan
- D. set routing-instances EVPN1 instance-type evpn
Answer: D
NEW QUESTION 16
You are using 802.1X in your access network consisting of EX Series switches. You recently had a failure with your RADIUS server which resulted in authenticating client devices being denied access to the network. You want to change this behavior so that authenticating clients are directed to a remediation VLAN.
Which RADIUS server failback setting satisfies this requirement?
- A. sustain
- B. deny
- C. move
- D. permit
Answer: C
Explanation:
Explanation/Reference:
NEW QUESTION 17
In a Layer 2 environment where 802.1X is deployed, which two statements are correct? (Choose two.)
- A. Extensible Authentication Protocol messages are exchanged between the authenticator and the authentication server.
- B. RADIUS messages are exchanged between the authenticator and the authentication server.
- C. Extensible Authentication Protocol messages are exchanged between the supplicant and the authenticator.
- D. RADIUS messages are exchanged between the supplicant and the authenticator.
Answer: B,C
NEW QUESTION 18
Click the Exhibit button.
Referring to the exhibit, how is R1 learning the route from R2?
R2 has an export policy with external type 2 configured.
- A. R2 has interface ge-0/0/2 configured in another area under OSPFv3.
- B. R2 has interface ge-0/0 configured as a passive interface under OSPFv3.
- C. R2 has interface ge-0/0/2 configured as a passive interface under OSPFv3.
- D. R2 has an interface policy with external type 1 configured.
Answer: D
NEW QUESTION 19
You are deploying IP phones in your Layer 2 network and are asked to ensure that the switch sends VLAN and CoS information to the IP phones automatically.
In this scenario, which protocol should be used?
- A. LLDP-MED
- B. PoE
- C. PoE+
- D. LLDP
Answer: A
NEW QUESTION 20
Your network is configured for EVPN load balancingon three different access switches During an outage, you notice that not all interfaces are receiving traffic as expected Which two requirements would you validate to identify this problem? (Choose two )
- A. Validate that all-active is configured for only interface per switch
- B. Validate that the all-active flag configured for multipleinterfaces on each switch
- C. Validate that the same esi value is only configured on one interface per switch
- D. Validate that the same esi value is configured on multiple interfaces on all switches.
Answer: B,D
NEW QUESTION 21
Click the Exhibit button.
You are configuring BGP policies for a site with a dual-homed connection as shown in the exhibit. You need all outbound traffic to egress the network through the link to ISP B by default. The ISPs should not be able to override this behavior through BGP attributes.
Which BGP attribute would you modify on the ISP-received routes to accomplish this objective?
- A. next-hop
- B. origin
- C. MED
- D. local preference
Answer: D
NEW QUESTION 22
Click the Exhibit button.
Referring to the exhibit, which statement is true?
- A. Additional users will automatically be allowed to connect to ge-0/0/15.
- B. The current device is authenticated using MAC RADIUS.
- C. Only 802.1X authentication will be used for devices connecting to ge-0/0/15.
- D. The current device was allowed after authentication attempts to the RADIUS server failed.
Answer: D
NEW QUESTION 23
Click the Exhibit button.
You are configuring an EVPN overlay to allow VLANs to be stretched between two campus sites, but EVPN routes are not being exchanged.
Referring to the exhibit, which configuration statement would solve this problem?
- A. Apply the delete protocols bgp groupEVPN cluster 172.1.1.55configuration on MX2.
- B. Apply the set protocols bgp group EVPN family inet-vpn anyconfiguration on MX1 and MX2.
- C. Apply the set protocols bgp group EVPN family evpn signaling configuration on MX2.
- D. Apply the delete protocols bgp group EVPN multipath multiple-as configuration on MX1 and MX2.
Answer: C
Explanation:
Explanation/Reference:
NEW QUESTION 24
A BA classifier, input policer, and a multifield classifier are applied to an interface.
In which order are these features processed?
- A. policer -> multifield classifier -> BA classifier
- B. policer -> BA classifier -> multifield classifier
- C. BA classifier -> multifield classifier -> policer
- D. multifield classifier -> BA classifier -> policer
Answer: B
NEW QUESTION 25
Click the Exhibit button.
You are investigating reports of increased latency and discover that some routes cause customer traffic to traverse a route reflector instead of the optimal path.
Referring to the exhibit, which configuration statement would solve the problem?
- A. delete protocols bgp group BGP-MESH export NHS
- B. set protocols bgp group BGP-MESH import NHS
- C. set policy-options policy-statement NHS term BGP_ROUTES from external
- D. delete protocols bgp group BGP-MESH peer-as
Answer: C
NEW QUESTION 26
Click the Exhibit button.
You recently implemented the configuration shown in the exhibit. After committing these changes, the community devices connected to AS-1 are not able to communicate with the appropriate community devices connected to AS-2.
What must be done to allow these community devices to communicate?
- A. You must configure an isolation VLAN ID under the vlan-priVLAN on the AS-2 switch.
- B. You must configure an isolation VLAN ID under the vlan-priVLAN on both switches.
- C. You must configure the ge-0/0/10 interface on AS-1 as the inter-switch link
- D. You must configure the ge-0/0/1 interface on both switches as the inter-switch links.
Answer: D
NEW QUESTION 27
Click the Exhibit button.
Which well-known community needs to be used to restrict 10.0.0.0/8 from being advertised to AS 2?
- A. no-publish
- B. no-advertise
- C. no-export-subconfed
- D. no-export
Answer: D
NEW QUESTION 28
Click the Exhibit button.
You have configured MSTP in your Layer 2 network. You are having problems with it establishing correctly.
Referring to the exhibit, what is causing the problem?
- A. You must assign a context ID number other than zero
- B. The revision number is the same on both devices
- C. The MSTI-to-VLAN mapping does not match
- D. The region name is not correct
Answer: C
NEW QUESTION 29
Exhibit:
A router is attempting to form an OSPF neighborship with another router However, the OSPF neighborship fails to establish completely Referring to the exhibit, what is the problem?
- A. There is an OSPF area mismatch
- B. There is an interface type mismatch
- C. There is an interface MTU mismatch
- D. There is an interface subnet mask mismatch
Answer: C
NEW QUESTION 30
Exhibit:
Referring to the log shown in the exhibit, what is the problem with the OSPF adjacency establishment?
- A. The interface IP addresses on the subnet are duplicates.
- B. The referenced IP address does not exist on the network segment.
- C. There is an MDS authentication mismatch.
- D. The OSPF database description packet is malformed.
Answer: A
NEW QUESTION 31
Click the Exhibit button.
You receive the same 100.200.0/16 route from all four ISPs to which you are connected.
Referring to the exhibit, which ISP's route will be selected as active?
- A. ISP-B
- B. ISP-D
- C. ISP-C
- D. ISP-A
Answer: D
NEW QUESTION 32
Exhibit:
YourNet is learning the 210.210.40.0/24 route from Provider A and Provider B YourNet would like to forward traffic destined to the 210.210.40.0/24 networking using Provider B.
Referring to the exhibit, how would you accomplish this task?
- A. Add the well-known no-export community to the routes learned through R2.
- B. Apply an export policy to R1's IBGP peers to set a higher local preference.
- C. Apply an export policy to R2's IBGP peers to set a Their local preference.
- D. Add the well-known no-export community to the routes learned through R1.
Answer: C
NEW QUESTION 33
Click the Exhibit button.
You are investigating reports of increased latency and discover that some routes cause customer traffic to traverse a route reflector instead of the optimal path.
Referring to the exhibit, which configuration statement would solve the problem?
- A. delete protocols bgp group BGP-MESH export NHS
- B. set protocols bgp group BGP-MESH import NHS
- C. set policy-options policy-statement NHS term BGP_ROUTES from external
- D. delete protocols bgp group BGP-MESH peer-as
Answer: C
Explanation:
Explanation/Reference:
NEW QUESTION 34
Exhibit.
You recently implemented the configurations shown in the exhibit. After committing these changes, the community devices connected to AS-1 are not able to communication with the appropriate community devices connected to AS-2.
What must be to allow these community devices to communicate?
- A. You must configure an isolation VLAN ID under the vlan-pri vlan on the AS-2 switch.
- B. You must configure to allow the ge-0/0/1 interface on AS-1 as the inter-switch.
- C. You must configure the ge-0/0/1 interface on both switchesthe inter-switch links.
- D. You must configure an isolation VLAN ID under the vlan-pri VLAN on both switches.
- E. You must configure the ge-0/0/10 interface on AS-1 as the inter-switch link.
Answer: C
NEW QUESTION 35
......
The benefit in Obtaining the Juniper JN0-648: Enterprise Routing and Switching, Professional (JNCIP-ENT) Exam Certification
- Juniper Service Provider Routing and Switching, Professional Certifications provide opportunities to get a job easily in which they are interested in instead of wasting years and ending without getting any experience.
- BraindumpsPass provides the latest Juniper JN0-648 dumps that will immensely help candidates to get good grades in their final Juniper JN0-648 exam.
- Juniper Service Provider Routing and Switching, Professional is distinguished among competitors. Juniper Service Provider Routing and Switching, Professional certification can give them an edge at that time easily when candidates appear for a job interview employers seek to notify something which differentiates the individual to another.
- Juniper Service Provider Routing and Switching, Professional Certification provides practical experience to candidates from all the aspects to be a proficient worker in the organization.
- Juniper Service Provider Routing and Switching, Professional know to use the tools to complete the task efficiently and cost-effectively than the other non-certified professionals lack in doing so.
- Juniper Service Provider Routing and Switching, Professional certification has more useful and relevant networks that help them in setting career goals for themselves. Juniper Service Provider Routing and Switching, Professional networks provide them with the right career direction that non-certified usually are unable to get.
- Juniper Service Provider Routing and Switching, Professional will be confident and stand different from others as their skills are more trained than non-certified professionals.
BraindumpsPass JN0-648 Exam Practice Test Questions : https://www.braindumpspass.com/Juniper/JN0-648-practice-exam-dumps.html