Free NS0-184 Exam Braindumps certification guide Q&A
NS0-184 Certification Overview Latest NS0-184 PDF Dumps
NetApp NS0-184 Exam Topics:
| Section | Objectives |
|---|---|
| Customer Handoff | - Describe the tools available to review an installation - Describe the process for handover of new ONTAP cluster installation to the customer - Identify how to create documentation |
| Basic Installation Topics and Tools | - Describe the required tools or documentation for preparing the installation of a new ONTAP cluster -Describe physical cabling of ONTAP nodes |
| ONTAP Concepts | - Identify how to update ONTAP - Identify ONTAP cluster controller components - Describe how to create aggregates - Describe the required steps for installation or expansion of an ONTAP cluster |
| ONTAP Configuration | - Describe how to add or remove nodes in an ONTAP cluster - Describe how to set up cluster peering - Describe how to implement security hardening - Describe support resources required for troubleshooting ONTAP installations |
| ONTAP Networking | - Describe how to configure ONTAP system networking - Describe network types used with ONTAP clusters |
NEW QUESTION 14
You are installing a new AFF A400 cluster that is running ONTAP 9.7 software. You are asked to attach an Amazon S3 cloud tier for FabricPool technology.
In this scenario, which two NetApp License File (NLF) types are supported for cloud tiering? (Choose two.)
- A. master
- B. term-based
- C. perpetual
- D. base
Answer: B,C
NEW QUESTION 15
What is the default shelf ID for disk shelves with IOM12 modules?
- A. 01
- B. 0
- C. 00
- D. 1
Answer: C
NEW QUESTION 16
You installed a new pair of Cisco 92300YC cluster switches at a customer's site. Before you install any files on the switch, you want to view the current configuration.
In this scenario, which command would you use to accomplish this task?
- A. fabricshow
- B. show running-config
- C. switchcfgshow
- D. config show
Answer: C
NEW QUESTION 17
You are installing a new FAS2750 cluster with 24 HDDs for a customer to run a NAS workload. The customer requests that the HA pair have only a single aggregate that is located on Node 1. Maximum capacity is required.
Which action must be performed to ensure that the customer's requests are satisfied?
- A. Assign all data LIFs to Node 1.
- B. Perform a takeover of Node 2 to ensure that it does not run.
- C. Assign all the data partitions from Node 2 to Node 1, and create a single aggregate.
- D. Assign all the partitioned disks from Node 2 to Node 1, and create a single aggregate.
Answer: A
NEW QUESTION 18
One of the nodes in your ONTAP 9.7 cluster has failed and is not coming back online.
Which two methods would you use to connect to the node failing to come back online? (Choose two.)
- A. Use the Intelligent Platform Management Interface.
- B. Use Secure Shell.
- C. Use the Service Processor Interface.
- D. Use Telnet.
Answer: B,C
NEW QUESTION 19
Click the Exhibit button.
You plan to install a new ONTAP cluster at a customer site by using the new ONTAP System Manager 9.7 GUI.
Referring to the exhibit, what must you do before you provision initial storage?
- A. Configure a remote tier.
- B. Configure protocols.
- C. Configure aggregates.
- D. Configure cluster LIFs.
Answer: C
NEW QUESTION 20
You must replace a FAS2750 switchless cluster with an AFF A220 switchless cluster for a customer. The customer requires that you transfer the data from the FAS2750 cluster to the AFF A220.
In this scenario, which two methods would you use to migrate the customer's data? (Choose two.)
- A. Establish an SVM-DR relationship between the two clusters and activate the destination SVM.
- B. Install SAS cables between the two clusters and use the vol move command.
- C. Remove all of the HDD drives from the FAS cluster and install them into the AFF cluster.
- D. Provide cluster switches and build a 4-node cluster, then use the vol move command.
Answer: B,D
NEW QUESTION 21
Click the Exhibit button.
As shown in the exhibit, you have an 8-node ONTAP 9.7 cluster. You are asked to set up a SnapMirror volume relationship between node-1 and node-8 in the same cluster.
In this scenario, which two network components are used by the SnapMirror volume? (Choose two.)
- A. cluster LIFs
- B. private network
- C. management LIFs
- D. client network
Answer: A,B
NEW QUESTION 22
You are installing a 4-node AFF A400 cluster and are asked to create a custom security message before and after user login.
Which two security features are used to perform this task? (Choose two.)
- A. AutoSupport
- B. motd
- C. banner
- D. EMS
Answer: A,C
NEW QUESTION 23
Before installing an 8-node cluster for a customer, you want to validate compatibility with existing hardware.
Which two tools would you use to validate the configuration? (Choose two.)
- A. Interoperability Matrix Tool
- B. Active IQ System Manager
- C. Hardware Universe
- D. Active IQ Config Advisor
Answer: A,D
NEW QUESTION 24
Click the Exhibit button.
A customer has two Cisco 40GbE data switches. They want to connect the switches to an AFF A400 HA pair. The switches and the AFF A400 are approximately seven meters apart.
Referring to the exhibit, which two supported actions would allow you to accomplish this task? (Choose two.)
- A. Install 10 meter NetApp supported copper cables.
- B. Change the requirement for Ethernet cables.
- C. Change the requirement for optical cables.
- D. Relocate the switches or the AFF A400 so that the distance is less than five meters.
Answer: A,B
NEW QUESTION 25
Before starting a base installation on an AFF A400, you need to find out the default cluster interconnect ports for the AFF A400 controllers.
In this scenario, which three resources would you use to find this information? (Choose three.)
- A. AFF FAS Documentation Center
- B. Active IQ Unified Manager
- C. Interoperability Matrix Tool (IMT)
- D. hardware installation setup poster
- E. Hardware Universe (HWU)
Answer: A,D,E
NEW QUESTION 26
What are two ways to identify an AFF All SAN Array system? (Choose two.)
- A. Use the cluster image show CLI command.
- B. View the ONTAP System Manager system nodes.
- C. Use the san config show CLI command.
- D. View the ONTAP System Manager cluster settings.
Answer: B,C
NEW QUESTION 27
You want to verify that connections are cables correctly and that shelf IDs are unique within an HA pair.
Which tool would be used to accomplish these tasks?
- A. Active IQ Config Advisor
- B. Cloud Insights
- C. System Diagnostics
- D. Active IQ Unified Manager
Answer: C
NEW QUESTION 28
While testing a recently installed FAS8700 cluster, a node fails. You now need to replace the impaired node.
In this scenario, which two statements are true? (Choose two.)
- A. You can change any drives or disk shelves as part of this replacement procedure.
- B. The boot device must remain intact and must not be removed from the impaired node.
- C. You must move the boot device from the impaired node to the replacement node.
- D. A controller model of the same type must be used to replace the impaired node.
Answer: C,D
NEW QUESTION 29
Click the Exhibit button.
You are installing a new FAS cluster. The management network must be on tagged VLAN 11 for remote administration by a service provider.
Referring to the exhibit, which two ports will allow service provider access to both cluster and node management LIFs? (Choose two.)
- A. e0b-11
- B. e0M-11
- C. e0a-11
- D. e0M
Answer: B,D
NEW QUESTION 30
Click the Exhibit button.
Referring to the exhibit, what information is forwarded to syslog after you enter the scripted install commands? (Choose two.)
- A. command history
- B. AutoSupport messages
- C. SNMP traps
- D. EMS messages
Answer: A,B
NEW QUESTION 31
What should you do to change the data protocol of a LIF?
- A. Delete and re-recreate the LIF.
- B. Put the LIF in another broadcast domain.
- C. Add the new data protocol to the LIF.
- D. Shut down the assigned port.
Answer: A
NEW QUESTION 32
In ONTAP 9.7 software, how many different replicated databases (RDBs) exist per node?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: C
NEW QUESTION 33
You have an AFF All SAN Array (ASA) cluster that is running ONTAP 9.7. The cluster is configured for Active Directory domain controller access using a domain tunnel.
In this scenario, which two licenses are enabled on the cluster? (Choose two.)
- A. NVMe
- B. iSCSI
- C. CIFS
- D. FCP
Answer: C,D
NEW QUESTION 34
......
NetApp NS0-184 Exam Certification Details:
| Duration | 90 minutes |
| Recommended Training | ONTAP Cluster Administration (vILT/ILT) Universal FAS Installation (WBT) ONTAP Hardware Component Troubleshooting and Analysis |
| Exam Code | NS0-184 NCSIE |
| Sample Questions | NetApp NS0-184 Sample Questions |
| Passing Score | 67% |
| Exam Name | Storage Installation Engineer ONTAP |
The Best Network Appliance NS0-184 Study Guides and Dumps of 2022: https://www.braindumpspass.com/NetworkAppliance/NS0-184-practice-exam-dumps.html
Top Network Appliance NS0-184 Exam Audio Study Guide! Practice Questions Edition: https://drive.google.com/open?id=19he09ww5J8BcLVPSlWkd4538_2BoOizI
